Soft Block Anchor 70mm

The Soft Block Anchor 70mm is a specialist fixing designed for reliable anchoring in soft
masonry substrates such as aerated concrete (Thermalite), lightweight blocks and other low‑density
blockwork. With an aggressive expansion design and deep engagement, this 70mm anchor provides
secure, load‑bearing fixings where standard plugs and screws can easily pull out.

The Soft Block Anchor 70mm has been developed to overcome the challenges of fixing into soft,
friable blocks where conventional plastic plugs provide inconsistent performance. Its design
allows the anchor to expand effectively within low‑density material, creating a secure mechanical
interlock while minimising the risk of the substrate crumbling around the fixing.

Typically used with a compatible screw (check product spec), the 70mm length provides deeper
embedment into soft blockwork, improving load capacity and overall security of the fixing. This
makes it an excellent choice for mounting timber battens, window and door frames, cable trays,
pipe clips, brackets, rails and other fixtures to aerated or lightweight block walls.

Suitable for internal applications (and some sheltered external uses depending on screw/fixture
choice), the Soft Block Anchor 70mm is widely used by builders, electricians, plumbers and
installers who regularly work with modern lightweight masonry.

Typical Use Cases

• Fixing timber battens and grounds to aerated / lightweight concrete blocks.
• Mounting window and door frames in soft block reveals (as part of a suitable fixing system).
• Securing pipe clips, cable trays, trunking and conduit to soft block walls.
• Installing brackets, rails, shelving supports and light services.
• General medium‑duty fixing into low‑density blockwork where standard plugs fail.

Installation & Usage Tips

• Use the correct drill size: Drill the hole diameter and depth specified for the anchor to achieve proper expansion.
• Drill in rotary mode only: Avoid hammer action in very soft blocks to reduce substrate damage.
• Clean the hole: Remove dust and debris before inserting the anchor to improve grip.
• Use appropriate screws: Match screw gauge and length to the anchor and fixture thickness as per manufacturer guidance.
• Avoid over‑tightening: Tighten screws firmly but do not over‑drive, which can crush soft blockwork and reduce holding power.

Technical Information (Typical)

Exact details may vary by manufacturer; always refer to the product label or technical data
sheet for your specific Soft Block Anchor 70mm. Typical characteristics include:

• Type: Expansion anchor/plastic plug for soft/lightweight blockwork.
• Length: 70mm overall anchor length (approx.).
• Substrates: Aerated concrete blocks, lightweight aggregate blocks, soft blockwork and other low‑density masonry.
• Installation: Pre‑drilled hole in rotary mode; insert anchor, then drive compatible screw.
• Recommended screw: Typically wood or multipurpose screw of specified gauge and length (check product data).
• Applications: Medium‑duty fixings in soft masonry; not intended as a substitute for heavy structural anchors.

For declared load values, edge and spacing distances, recommended drill size and detailed
installation instructions, consult the manufacturer’s technical documentation for the
Soft Block Anchor 70mm.

Key Features

• Designed for low‑density blockwork – performance where standard plugs underperform.
• Deep 70mm anchor length – improved embedment and pull‑out resistance.
• Simple installation – uses standard drills and compatible screws.
• Versatile fixing solution – ideal for a wide variety of services and light structural elements.
• Trade‑ready performance – consistent, repeatable results in modern soft block substrates.

Frequently Asked Questions (FAQs)

Common Uses / How to Use

To get the best from the Soft Block Anchor 70mm:

1. Mark the fixing position on the soft blockwork.
2. Drill a hole to the specified diameter and depth using rotary‑only mode where possible.
3. Clean out dust from the hole with a blower or brush.
4. Insert the Soft Block Anchor 70mm fully into the hole until flush with the surface.
5. Position the fixture (batten, bracket, clip, frame, etc.) over the anchor.
6. Drive the recommended screw into the anchor until the fixture is secure; avoid over‑tightening.